Contemporary-control-systems BASrouter Installation Guide (Firmware 2.x) Manual de usuario

BASRT-B BAS Router BACnet® Multi-network Router Installation Guide TD071200-0IK For Firmware Versions 2.x

TD071200-0IK 10 Figure 10 — 3-wire MS/TP Bus with Separate Power Sources 3.2 Limited Power Sources The router should be powered by a limited

TD071200-0IK 11 5 Operation 5.1 MS/TP Port The MS/TP port uses an isolated EIA-485 transceiver connected to a 3-pin removable connector (Figure 1).

TD071200-0IK 12 Figure 11 — Isolated EIA-485 Transceiver Circuitry The router can address 254 MS/TP devices and supports 31 full-load devices on the

TD071200-0IK 13 6 Webpage Configuration Each router contains an interactive web server, accessible from any Internet-compatible PC on the local netw

TD071200-0IK 14 Figure 13 — Steps for Changing the IP Address of the PC Used for Setup On some systems, this option is: ―My Network Places‖.

TD071200-0IK 15 After entering the router’s IP address into your browser’s address field, you will see the Logon Screen of Figure 14. The de

TD071200-0IK 16 6.1 Device Parameters 6.1.1 Device Name (Default Value = BASRT-Bxxxxxx) Starting with firmware 2.6.0, this editable field

TD071200-0IK 17 NOTE: Although they may share the same Ethernet physical network, BACnet Ethernet devices as well as BACnet/IP devices must

TD071200-0IK 18 6.4 MS/TP Parameters 6.4.1 MS/TP MAC (Default Value = 00) This is the unique 8-bit (0–127) MAC address of the router’s

TD071200-0IK 19 those passed by the router from BACnet/IP. The default value usually provides good performance. 6.4.5 MS/TP Baud Rate (Default Va

TD071200-0IK 2 Trademarks Contemporary Controls, ARC Control, ARC DETECT, BASautomation, EXTEND-A-BUS, RapidRing, and CTRLink are trademarks or regis

TD071200-0IK 20 7 Advanced Features The right side of the Router Configuration Page (Figure 15) has the following three buttons that access advanced

TD071200-0IK 21 NPDU IP Address field. The NAT router must be configured such that communications to the NAT router on the Secondary BACnet/IP net

TD071200-0IK 22 If you click the button labelled Foreign Device Registration (FDR), the screen shown in Figure 18 appears (unless you have no

TD071200-0IK 23 The remaining information in Figure 19 reports the instantaneous MS/TP state of the router and is documented in the MS/TP p

TD071200-0IK 24 8 Warranty Contemporary Controls (CC) warrants this product to the original purchaser for two years from the product shipping date.

TD071200-0IK 3 Contents 1 Introduction ... 4 2 Specifications ...

TD071200-0IK 4 1 Introduction The BASRT-B is a multi-network router, sharing messages among BACnet/IP, BACnet Ethernet and MS/TP networks. T

TD071200-0IK 5 2 Specifications 2.1 Electrical INPUT DC AC Voltage (±10%): 24 V 24 V Power: 2 W 4 VA Frequency: N/A 47–63 Hz 2.2 Environ

TD071200-0IK 6 2.7 Connectors 3-pin (MS/TP) Pin Assignments (Also explained on product label) RJ-45 (MDI Ethernet) Pin Assignments 1 TD + 3 RD +

TD071200-0IK 7 3 Power The BASRT-B requires 24 VAC or 24 VDC (see Figure 6) while drawing no more than 4 VA of power. The recommended con

TD071200-0IK 8 side of the connection. Connect the HOT side of the secondary to either the HI or the HIB input on the router and the LO side to COM

TD071200-0IK 9 Figure 8 — 3-wire MS/TP Bus with Shared Power Source For MS/TP devices that use a power source separate from the BASRT-B, see